Typebar - Revision history

Cerafuki: Redirected page to Typebars

2023-09-12T16:24:16Z

Redirected page to Typebars

Cerafuki: Blanked the page

2023-09-07T14:48:10Z

Blanked the page

Winfried320: Created page with "The '''typebar''' is a metal arm with a typeslug at its end, which is responsible for striking the ribbon and paper when typing. Each typebar corresponds to one key on a typew..."

2023-09-07T11:54:01Z

Created page with "The '''typebar''' is a metal arm with a typeslug at its end, which is responsible for striking the ribbon and paper when typing. Each typebar corresponds to one key on a typew..."

New page

The '''typebar''' is a metal arm with a typeslug at its end, which is responsible for striking the ribbon and paper when typing. Each typebar corresponds to one key on a typewriter. All of the typebars form a so called "type basket". On some typewriters, the shift function is intitated by lowering the level of the type basket. On most machines, the typebars have a pivot point in the "segment". They stay in a resting position, laying on the "typebar rest", until the corresponding key has been pressed.

Although this mechanism is most commonly used, there are many typewriters with "noiseless" or "thrust" mechanisms, which operate in a different fashion. There are also many machines that use a "type element" instead of typebars.

__TOC__

==Commonly occurring problems==
A sticky segment is a common problem when fixing a machine that has not been used for a while. Flushing it with mineral spirits or isopropyl alcohol and using a toothbrush to get in the slots is recommended. Afterwards, it is best to use compressed air to get all solvent and gunk out. Note that when working with mineral spirits or other paint thinners, they should be kept away from all painted surfaces, as they will eat through the paintjob and damage it.

Another common problem are bent typebars. It is important to be careful when fixing those, because there is a risk of the bar breaking off. It's advised to carefully bend the typebar back into its proper position using fingers or pliers. There also are typewriter-specific tools for the job, but those are hard to come by.

It's also a common occurrence for a typewriter to not be "soundproofed". This means that the typebar rest is not covered by anything, so when a typebar falls back onto it, there is a sound of metal hitting metal. This makes typing much louder. Most typewriters were soundproofed when manufactured, with a piece of leather or felt, attached to the typebar rest, but those have often fallen off at some point. To make typing quieter, it is recommended to resoundproof the machine. A strip of felt/leather can easily be glued to it. It is important that that strip is not too thick - if it raises the resting level of the typebars too much, it will cause them to jam together.

← Older revision	Revision as of 16:24, 12 September 2023
Line 1:	Line 1:
−	+	#REDIRECT [[Typebars]]

← Older revision		Revision as of 14:48, 7 September 2023
Line 1:		Line 1:
−	The '''typebar''' is a metal arm with a typeslug at its end, which is responsible for striking the ribbon and paper when typing. Each typebar corresponds to one key on a typewriter. All of the typebars form a so called "type basket". On some typewriters, the shift function is intitated by lowering the level of the type basket. On most machines, the typebars have a pivot point in the "segment". They stay in a resting position, laying on the "typebar rest", until the corresponding key has been pressed.

−	Although this mechanism is most commonly used, there are many typewriters with "noiseless" or "thrust" mechanisms, which operate in a different fashion. There are also many machines that use a "type element" instead of typebars.
−
−	~~__TOC__~~
−
−
−	~~==Commonly occurring problems==~~
−	A sticky segment is a common problem when fixing a machine that has not been used for a while. Flushing it with mineral spirits or isopropyl alcohol and using a toothbrush to get in the slots is recommended. Afterwards, it is best to use compressed air to get all solvent and gunk out. Note that when working with mineral spirits or other paint thinners, they should be kept away from all painted surfaces, as they will eat through the paintjob and damage it.
−
−	Another common problem are bent typebars. It is important to be careful when fixing those, because there is a risk of the bar breaking off. It's advised to carefully bend the typebar back into its proper position using fingers or pliers. There also are typewriter-specific tools for the job, but those are hard to come by.
−
−	It's also a common occurrence for a typewriter to not be "soundproofed". This means that the typebar rest is not covered by anything, so when a typebar falls back onto it, there is a sound of metal hitting metal. This makes typing much louder. Most typewriters were soundproofed when manufactured, with a piece of leather or felt, attached to the typebar rest, but those have often fallen off at some point. To make typing quieter, it is recommended to resoundproof the machine. A strip of felt/leather can easily be glued to it. It is important that that strip is not too thick - if it raises the resting level of the typebars too much, it will cause them to jam together.