Difference between revisions of "Common Questions"
| Line 1: | Line 1: | ||
Others have felt your pain. | Others have felt your pain. | ||
| + | |||
| + | == How To == | ||
| + | |||
| + | === Reconnect my my draw band === | ||
| + | |||
| + | The concept is similar across many typewriters. Check out some of these videos, and of course search google. | ||
| + | |||
| + | [https://www.youtube.com/watch?v=b-R_85kmKMM Royal Typewriter Draw Band String Cable Reattached Main Spring Wound] | ||
| + | |||
| + | [https://www.youtube.com/watch?v=a7WUF8hV-0U Royal "O" Typewriter Draw Band Repaired Replaced Mainspring Wound] | ||
== Cleaning == | == Cleaning == | ||
| Line 15: | Line 25: | ||
An air compressor can send piece of your typewriter flying if they're not secure, so some prefer a low powered vacuum with a dust cup with filter. There are ones for cleaning electronics/keyboards that can serve this purpose. Others used canned air or low pressure compressors. | An air compressor can send piece of your typewriter flying if they're not secure, so some prefer a low powered vacuum with a dust cup with filter. There are ones for cleaning electronics/keyboards that can serve this purpose. Others used canned air or low pressure compressors. | ||
| − | == | + | == Problems == |
=== My ribbon vibrator (piece that holds ribbon) sticks === | === My ribbon vibrator (piece that holds ribbon) sticks === | ||
Could be gunked up or need to be re-formed. Definitely rule out all other potential causes before bending the metal. | Could be gunked up or need to be re-formed. Definitely rule out all other potential causes before bending the metal. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
===The tops of my letters get cut off=== | ===The tops of my letters get cut off=== | ||
This could be because your ribbon vibrator (the part that raises the ribbon up) is not raising enough OR that you need some adjustment to the shift mechanism. A fix for the former can be easier and should be attempted first. However, before any repairs should be attempted, make sure it is *clean*. Dirt and will also prevent it from raising high enough. On a few machines, an improperly threaded ribbon will also cause this issue. | This could be because your ribbon vibrator (the part that raises the ribbon up) is not raising enough OR that you need some adjustment to the shift mechanism. A fix for the former can be easier and should be attempted first. However, before any repairs should be attempted, make sure it is *clean*. Dirt and will also prevent it from raising high enough. On a few machines, an improperly threaded ribbon will also cause this issue. | ||
Revision as of 20:54, 27 September 2020
Others have felt your pain.
Contents
How To
Reconnect my my draw band
The concept is similar across many typewriters. Check out some of these videos, and of course search google.
Royal Typewriter Draw Band String Cable Reattached Main Spring Wound
Royal "O" Typewriter Draw Band Repaired Replaced Mainspring Wound
Cleaning
Help! There's white powder on my keys!
No, typewriters do not automatically generate cocaine.
White powder on 1950s and later plastic keys is a result of a chemical process known as degassing and a result of decomposition in the plastic itself. It can be removed with vigorous dry rubbing, with bare fingers or gently with a Scotch Brite pad. Some say that WD-40 on your fingers may help. Do a couple now, do something else, do a couple more. You might get blisters. Have fun!
Removing hair, dust, and other gunk
A detailing brush with a small handheld vacuum that's used for computers can be effective at removing hair and other debris. Other tools one might use are a dental pick, a paint brush, and pipe/straw cleaners (single use or reusable, hard and soft). Using tools can be more effective than canned air at times.
An air compressor can send piece of your typewriter flying if they're not secure, so some prefer a low powered vacuum with a dust cup with filter. There are ones for cleaning electronics/keyboards that can serve this purpose. Others used canned air or low pressure compressors.
Problems
My ribbon vibrator (piece that holds ribbon) sticks
Could be gunked up or need to be re-formed. Definitely rule out all other potential causes before bending the metal.
The tops of my letters get cut off
This could be because your ribbon vibrator (the part that raises the ribbon up) is not raising enough OR that you need some adjustment to the shift mechanism. A fix for the former can be easier and should be attempted first. However, before any repairs should be attempted, make sure it is *clean*. Dirt and will also prevent it from raising high enough. On a few machines, an improperly threaded ribbon will also cause this issue.
